IDE -> USB

[ref=443190]KC6994[/ref]  在 2005-12-13 03:46 發表:


Jumper係咪set 左master?

我已把所有jumper拔掉.

[ref=443183]kata_kin[/ref]  在 13/12/2005 21:40 發表:

隻HD係轉既,
而且幾震.

...

harddisk會震!?
震得幾厲害呀?
如果震到好似手機震果種ge話
咁隻harddisk都可以certify

[ref=443190]KC6994[/ref]  在 13/12/2005 21:46 發表:
Jumper係咪set 左master?

外置harddisk有無問題
理論上同jumper setting無關

[ref=443193]kata_kin[/ref]  在 2005/12/13 09:51 PM 發表:



我已把所有jumper拔掉.

無jumper？？
個人估計有些硬碟會拒絕工作
建議set 成CS

[ref=443204]superay[/ref]  在 2005-12-13 03:59 發表:



無jumper？？
個人估計有些硬碟會拒絕工作
建議set 成CS

我原本就係set做cable select,
不過一樣都係冇反應.

剛剛再試,
發現當我remove usb時,統話係detect到有磁碟機的.

(但係在「我的電腦」就一個folder都冇)

[ Last edited by kata_kin on 2005-12-13 at 04:11 ]

[ref=443197]kychung[/ref]  在 2005-12-13 03:52 發表:



harddisk會震!?
震得幾厲害呀?
如果震到好似手機震果種ge話
咁隻harddisk都可以certify

係好似平時運作咁即.
應該未certify

另外插usb時, 是否需要裝任何程式?
http://www.seagate.com/support/disc/utils.html

[ Last edited by kata_kin on 2005-12-13 at 04:23 ]

[ref=443215]kata_kin[/ref]  在 13/12/2005 22:09 發表:



係好似平時運作咁即.
應該未certify

另外插usb時, 是否需要裝任何程式?
http://www.seagate.com/support/disc/utils.html

[ Last edited by kata_kin on 2005-12-13 at 04:23 ]

harddisk 本身就唔駛 driver ge
但係個IDE->USB介面駛唔駛裝左driver至work就唔知啦
因為我未用過#

[ref=443506]kychung[/ref]  在 2005-12-14 03:16 發表:



harddisk 本身就唔駛 driver ge
但係個IDE->USB介面駛唔駛裝左driver至work就唔知啦
因為我未用過#

係唔駛既.

Can I use this cable for a combo drive (dvd+cd writer)? I've tried and it was detected and can open and close its door (with the button on the drive only) but could not read anything from the disk in the drive.

Do I have to do any settings first? #:-[ I use Win XP so there's no need to use to CD driver for the cable.

[ Last edited by rainbowbus on 2005-12-14 at 12:56 ]

[ref=443204]superay[/ref]  在 2005-12-13 09:59 PM 發表:



無jumper？？
個人估計有些硬碟會拒絕工作
建議set 成CS

使用這些轉接器，
通常都要把硬碟設定成MASTER/Single才能正常運作。